Genarator arbitralny AFG-3081 80MHz

Zapytaj o produkt +
firma gwinstek

Opis

NOWA SERIA GENERATORÓW ARBITRALNYCH AFG-3000

DOSTĘPNE DWA MODELE:

  • AFG-3081 80MHz
  • AFG-3051 50MHz

Charakterystyka ogólna:

  • Szeroki zakres częstotliwości od 1uHz do 80/50MHz
  • Dostępna szeroka gama sygnałów
  • Szybkość próbkowania 200MSa/s
  • 16-bit Rozdzielczość Amplitudy
  • Wybrane wyjście z pamięcią przebiegów 1Mpunktów
  • 4.3" wysokiej rozdzielczości wyświetlacz LCD
  • Cztery sposoby generowania przebiegów arbitralnych z panelu przedniego, generowanie z pliku CSV, Direct Waveform Reconstruction (DWR), Arbitrary Waveform Editing PC Software
  • Przełącznik impedancji / pomoc na wyświetlaczu
  • Interfejsy USB, RS-232, GPIB
 
AFG-3081
AFG-3051
Waveforms
Sine, Square, Ramp, Pulse, Noise, DC, Sin(x)/x, Exponential Rise, Exponential Fall, Negative Ramp
Arbitrary Waveforms
ARB Function
Built in
Sample Rate
200 MSa/s
Repetition Rate
100MHz
Waveform Length
1M points
Amplitude Resolution
16 bits
Non-Volatile Memory
Ten 1M waveforms(1)
User define Output Section
Any section from 2 to 1M points
User define Mark Output
Any section from 2 to 1M points
Frequency Characteristics
Range
Sine
80MHz
50MHz
Square
Triangle, Ramp
1MHz
Resolution
1uHz
Accuracy
Stability
±1 ppm 0 to 50?
±0.3 ppm 18 to 28?
Aging
±1 ppm, per 1 year
Tolerance
? 1 uHz
Output Characteristics(2)
 
 
Amplitude
Range
10 mVpp to 10 Vpp( into 50Ω)
 20 mVpp to 20 Vpp(open-circuit)
Accuracy
± 1% of setting ±1 mVpp
(at 1 kHz,>10 mVpp)
Resolution
0.1 mV or 4 digits
Flatness
± 1% (0.1dB)  <10 MHz  
± 2% (0.2 dB) 10 MHz to 50 MHz 
± 10% (0.9 dB) 50 MHz to 70 MHz
± 20% (1.9 dB) 70 MHz to 80 MHz 
(sinewave relative to 1 kHz)
Units
Vpp, Vrms, dBm,
Offset
Range
±5 Vpk ac +dc (into 50Ω)
±10Vpk ac +dc (Open circuit)
Accuracy
1% of setting + 2 mV+ 0.5% of amplitude
Waveform Output
Impedance
50Ω typical (fixed)
> 10MΩ (output disabled)
Protection
Short-circuit protected
Overload relay auto-matically disables main output
SYNC Output
Level
TTL-compatible into>1kΩ
Impedance
50Ω nominal
Sinewave Characteristics
Harmonic Distortion(5)
–60 dBc   DC?1 MHz, Ampl?3 Vpp
–55 dBc   DC?1 MHz, Ampl?3 Vpp
–45 dBc   1MHz?5 MHz, Ampl?3 Vpp
–30 dBc   5MHz?80 MHz, Ampl?3 Vpp
Total Harmonic Distortion
< 0.2%+0.1mVrms
DC to 20 kHz
Spurious (non-harmonic)(5)
–60 dBc   DC?1 MHz
–50 dBc   1MHz?20MHz
–50 dBc+ 6 dBc/octave 1MHz?80MHz
Phase Noise
?-65dBc typical 10MHz, 30 kHz band
?-47dBc typical 80MHz, 30 kHz band
Square wave Characteristics
Rise/Fall Time
<8 nS(3)
Overshoot
< 5%
Asymmetry
1% of period+1 ns
Variable Duty Cycle
20.0% to 80.0% ? 25 MHz   
  40.0% to 60.0%  25?50MHz  
50.0%(Fixed)     50?80MHz   
Jitter
0.01%+525ps  ? 2 MHz
0.1%+75ps  ? 2 MHz  
Ramp Characteristics
Linearity
? 0.1% of peak output
Variable Symmetry
0% to 100%
Pulse Characteristics
Period
20ns? 2000s
Pulse Width
8ns? 1999.9s
Minimum Pulse Width:
     8nS when FREQ?50MHz
     5% of setting period when FREQ?6.5MHz
Resolution:
     1nS when FREQ?50MHz
     1% of setting period when FREQ?6.5MHz
Overshoot
<5%
Jitter
100 ppm +50 ps
AM Modulation
Carrier Waveforms
Sine, Square, Triangle, Ramp, Pulse, Arb
Modulating Waveforms
Sine, Square, Triangle, Up/Dn Ramp
Modulating Frequency
2 mHz to 20 kHz
Depth
0% to 120.0%
Source
Internal / External
FM Modulation
Carrier Waveforms
Sine, Square, Triangle, Ramp
Modulating Waveforms
Sine, Square, Triangle, Up/Dn Ramp
Modulating Frequency
2 mHz to 20 kHz
Peak Deviation
DC to 80 MHz
DC to 50 MHz
Source
Internal / External
PWM
Carrier Waveforms
Square
Modulating Waveforms
Sine, Square, Triangle, Up/Dn Ramp
Modulating Frequency
2 mHz to 20 kHz
Deviation
0% ? 100.0% of pulse width
Source
Internal / External
FSK
Carrier Waveforms
Sine, Square, Triangle, Ramp, Pulse
Modulating Waveforms
50% duty cycle square
Internal Rate
2 mHz to 100 kHz
Frequency Range
DC to 80 MHz
DC to 50 MHz
Source
Internal / External
SWEEP
Waveforms
Sine, Square, Triangle, Arb
Type
Linear or Logarithmic
Direction
Up or Down
Start F / Stop FREQ
100 uHz to 80 MHz
100 uHz to 50 MHz
Sweep Time
1 ms to 500 s
Trigger
Single, External, Internal
Marker
Falling edge of Mark signal
(Programmable frequency)
Source
Internal / External
BURST
Waveforms
Sine, Square, Triangle, Ramp
Frequency
1 uHz to 80 MHz(4)
1 uHz to 50 MHz(4)
Burst Count
1 to 1000000 cycles or Infinite
Start / Stop Phase
-360.0?to +360.0?
Internal Period
1 ms to 500 s
Gate Source
External Trigger
Trigger Source
Single, External or Internal Rate
Trigger Delay   
N-Cycle, Infinite: 0s to 85 s
External Modulation Input
Type
for AM, FM, Sweep, PWM
Voltage Range
± 5V full scale
Input Impedance
10kΩ
Frequency
DC to 20 kHz
External Trigger Input
Type
for FSK, Burst, Sweep
Input Level
TTL Compatible
Slope
Rising or falling(selectable)
Pulse Width
> 100 ns
Input Impedance
10kΩ,DC coupled
Latency
Sweep
< 10 us (typical)
Burst
< 100 ns (typical)
Jitter
Sweep
2.5 us
Burst
1 ns; except pulse,300 ps
Modulation Output
Type
for AM, FM, Sweep, PWM
Amplitude
Range
?1Vpp
Impedance
> 10kΩ typical (fixed)
Trigger Output
Type
for Burst, Sweep
Level
TTL Compatible into 50Ω
Pulse Width
> 450 ns
Maximum Rate
1 MHz
Fan-out
?4 TTL load
Impedance
50Ω typical
Marker Output
Type
for ARB, Sweep
Level
TTL Compatible into 50Ω
Fan-out
?4 TTL load
Impedance
50Ω typical
Store/Recall
10 Groups of Setting Memories
Interface
GPIB, RS232, USB
Display
4.3 inch TFT LCD
480 × 3 (RGB) × 272
System Characteristics
Configuration Times
(typical)
Function Change:
      Standard—->102ms
      Pulse——–>660ms
      Built-In Arb- >240ms
Frequency Change: 24ms
Amplitude Change: 50ms
Offset Change: 50ms
Select User Arb: < 2s for 1M points
Modulation Change: < 200ms
Arb Download Times
(typical)
Binary Code
ASCII Code
GPIB / RS-232 (115 Kbps)
USB(Device)
USB(Host)
1M points
189 Sec
34 Sec
70 Sec
512K points
95 Sec
18Sec
35 Sec
256K points
49 Sec
9 Sec
18 Sec
64K points
16 Sec
3 Sec
6 Sec
16K points
7 Sec
830mS
1340 mS
8K points
6 Sec
490mS
780mS
4K points
6 Sec
365mS
520 mS
2K points
5 Sec
300mS
390 mS
General Specifications
Power Source
 AC100?240V , 50?60Hz
Power Consumption
65 VA
Operating Environment
Temperature to satisfy the specification :  18 ~ 28?C
Operating temperature : 0 ~ 40?C
Relative Humidity:
≤ 80%, 0 ~ 40°C
≤ 70%, 35 ~ 40°C
Installation category? CAT ?
Operating Altitude
2000 meters
Pollution Degree
IEC 61010 Degree 2, Indoor Use
Storage Temperature
 -10 ~ 70?C, Humidity: ≤70%
Dimensions (WxHxD)
Bench Top : 265 (W) x 107 (H) x 374 (D)
Weight
Approx. 4kg
Safety Designed to
EN61010-1
EMC Tested to
EN 55011, IEC-61326-1
Accessories
GTL-110× 1
  Instruction Manual×1
Power cord×1
(1). A total of ten waveforms can be stored.(Every waveform can composed of 1M points maximum.)
(2). Add 1/10th of output amplitude and offset specification per ?C for operation outside of 0?C to 28?C range (1-year specification).
(3). Edge time decreased at higher frequency.
(4). Sine and square waveforms above 25 MHz are allowed only with an "Infinite" count.
(5). Harmonic distortion and Spurious noise at low amplitudes is limited by a -70 dBm floor.

 

Marka

GW Instek

firma gwinstek